|
Product Data Sheet |
|
Product Description |
Kryptaglow®
Clear Protective Topcoat #1102 is a fast dry, water reducible finish that
dries to a crystal clear finish.
This product will enhance the beauty of Kryptaglow® Glow
Paint. |
|
|
|
Intended Uses |
Formulated
for use on Kryptaglow® Glow Paint.
|
|
|
|
Physical Properties |
Color Finishes Resin
Type Reduction
and Clean-up Solvent Solids
by Weight Solids
by Volume Dry
Film Thickness per Coat Wet
Film to Achieve DFT Theoretical
Coverage @ 1 mil Coverage
at Recommended DFT2 Drying
Times3 @
70ºF (21ºC) and
50% R.H. Recoat
1 to 2 hours VOC’s |
Appears
milky in the can but dries to a crystal clear finish. Gloss
60+ @ 60º Satin
625-30 @ 60º Acrylic Water 33% 31% 1
- 2 mils 3
– 6.5 mils 497
ft2/gallon 248-489
ft2/gallon Touch
10 minutes Tack
Free 1 hour Through
2 to 4 hours Recoat
after tack free 280
grams/liter |
|
|
|
1 Waterborne clears may
have a tendency to yellow over solvent/oil-based white or pastel colored
paints. In addition, oil-based
paints must be completely dry before topcoating with Kryptaglow® Paints. 2 Spread rates are
estimates based on products volume solids and make no allowance for material
loss during application. Actual
spread rates may vary dependent on applicator experience, surface porosity
and texture. 3 Dry times may vary
depending upon temperature, humidity and degree of air movement. |
|
|
|
specifications |
Kryptaglow®
Clear Protective Topcoat #1102 may be used as a clear protective coat on
surfaces painted with latex glow paint.
A test area is recommended to ensure the final appearance is
satisfactory. This
product meets or exceeds Master Painters Institute (MPI) #128 and #130
approval standards. |
Formulated
for use on Kryptaglow® Glow Paint.
|
|
Surface Preparation |
The
wood surface must be clean, dry and free from dirt, dust, wax and
grease. Surfaces must be
properly prepared and primed prior to application of this product. Bare
Wood Surfaces Sand
the wood thoroughly. Begin with
a medium grit sandpaper progressing to a fine grit. Always sand in the direction of the wood grain. Sand smooth and remove dust particles
with a rag dampened with water. Previously
Finished Wood Surfaces Sand
with a fine grit sandpaper to remove surface imperfections and gloss. Remove all sanding dust with a clean
rag dampened with water. |
|
|
|
Application |
·
DO
NOT SHAKE! Stir material prior
and during use ·
Equipment
must be clean prior to start.
Flush airless lines with clean water ·
Apply
by brush, roller or spray. A
good quality synthetic brush will make application easier. Use a ¼” nap mohair or
foam roller cover. An airless
tip size of 0.011 to 0.013 is recommended. ·
Apply
the product in full even coats and maintain a wet edge. If brushing, apply liberally, working
quickly to insure an even coat. ·
Allow
the product to dry 1 to 2 hours before recoating. Sand lightly between coats with a very fine sandpaper (220
grit) to produce a finer finish.
Remove sanding dust with a damp cloth. Three coats are recommended for greatest durability. ·
Thinning
is normally not required. |
|
|
environmental variables |
Minimum
surface and air temperature required for application is 50ºF (10ºC). Curing is affected by temperature,
humidity and air movement. The
minimums must be maintained for at least eight (8) hours in order to achieve
proper film formation.
Application at elevated temperatures and/or low humidity may require
special application procedures to achieve proper film formation. Recommended conditions:
temperatures between 60ºF (15 ºC) and 90ºF (32ºC);
relative humidity between 30% and 70%. |
|
|
Clean up |
Clean
up all equipment using warm water.
Rinse with clean water and allow to dry. |
|
|
|
Safety Precautions |
For
interior use only Do
not apply below 50
ºF Protect
from freezing Not
for use on horizontal surfaces Do
not take internally Use
with adequate ventilation Keep out of reach of children For
more detailed recommendations, please contact your local Kryptaglow
Representative |
|
|
Co-Leash, Inc.
P.O. Box 272672
Tampa, FL 33688
(P) 813/920-1910 (F)
813/792-1418
www.kryptaglow.com